Last Tuesday, I watched a Samsung front-loader in Jumeirah Lakes Towers literally tear itself apart. The owner ignored a grinding noise for three weeks because “it still cleaned the clothes.” By the time we arrived, the drum bearing had disintegrated and punched through the outer tub. Repair cost: AED 1,850. A bearing replacement three weeks earlier would have cost AED 450.
That’s the thing about washing machine repair Dubai. The 45-degree heat, the hard water loaded with minerals, and the dust that infiltrates even the newest apartments create a perfect storm for appliance failure. Your machine isn’t just fighting dirty laundry. It’s battling environmental conditions that would destroy washers in London or New York within months.
I’ve spent eleven years repairing washing machines across Dubai, from studio apartments in Discovery Gardens to villas in Arabian Ranches. I’ve seen LG machines with control boards fried by power surges during summer peak demand. I’ve pulled out Samsung door seals so covered in mold they looked like science experiments. I’ve diagnosed Bosch washers with drums seized solid from limescale buildup that looked like concrete. You’ll discover here the exact sounds that mean “call now” versus “monitor it,” the error codes that indicate simple fixes versus expensive replacements, and the three maintenance tasks that could add five years to your machine’s life in Dubai’s brutal climate. Most importantly, you’ll learn which problems cost AED 200 to fix today but AED 2,000 if you wait a month.
Why Your Washing Machine Fails Faster in Dubai
Before we dive into the warning signs, you need to understand why washing machines die younger in Dubai. I’m not talking about normal wear and tear. I’m talking about environmental factors that compound every minor issue into major failures.
Dubai’s water contains 300-500 mg/L of dissolved minerals. That’s considered “very hard” by international standards. Every wash cycle deposits calcium and magnesium onto your heating element, inside your pump, and throughout your drum bearings. Within 18 months, I’ve seen heating elements so coated with limescale they couldn’t transfer heat. The machine ran longer cycles, consumed more electricity, and eventually burned out the control board trying to reach temperature.
The heat matters more than most people realize. When your machine sits in a service room where temperatures hit 50 degrees Celsius in summer, rubber seals become brittle and crack. Hoses develop weak spots. Electronic components on the control board degrade faster than manufacturer specifications account for. LG and Samsung both use rubber compounds designed for European climates. Those materials start breaking down after just two Dubai summers.
Sign 1: Your Machine Sounds Like It’s Destroying Itself
The Grinding Death Spiral
Here’s the noise that should make you stop the machine immediately and call a technician: a loud, continuous grinding sound during the spin cycle that gets progressively worse. This is drum bearing failure, and it’s the most expensive common repair at AED 800-1,200 for parts and labor. I diagnosed this exact problem last month in a Bosch Serie 6 that was only four years old. The owner heard the grinding for two weeks but kept using it because “the clothes came out clean.” By the time I opened it up, metal shavings from the destroyed bearing had contaminated the drum seal and damaged the spider arm. Total repair: AED 1,650. If she’d called when the noise started, we would have caught it at AED 750.
Drum bearings fail in Dubai faster than anywhere else I’ve worked. The combination of hard water corroding the bearing seal and heat degrading the lubricant means most machines need bearing replacement between years 4-6 instead of the 8-10 years manufacturers project.
The Thumping That’s Actually Normal
Not every noise means disaster. Heavy thumping during the spin cycle usually indicates an unbalanced load. Your machine is designed to thump when towels or bedsheets clump on one side. Stop the machine, redistribute the load, and restart. If the thumping continues with a balanced load, then you have a problem. I’ve done service calls where the “emergency” was just an unbalanced comforter. The customer paid AED 150 for a diagnosis that took 30 seconds. Learn to distinguish between mechanical failure and user error.
The Squeaking Mystery
High-pitched squeaking during agitation points to one of three issues: worn drive belt (AED 250-350 to replace), faulty drum pulley (AED 300-450), or failing motor bearings (AED 600-900). The good news is that all three are fixable before they cause cascade failures. Here’s how to diagnose: if squeaking only happens during agitation but stops during drain and spin, it’s the drive belt. If it happens throughout all cycles, suspect motor bearings. If it’s intermittent and changes pitch, you likely have a pulley issue.
When Banging Means Big Problems
Sharp metallic banging that sounds like something hitting the drum usually means foreign objects (coins, bra underwires, buttons) have fallen into the sump or pump. I’ve pulled out everything from AED 1 coins to children’s toys. This requires immediate attention because these objects can puncture the drum or damage the pump impeller.
Cost to remove foreign objects: AED 200-300. Cost to replace a punctured drum: AED 1,200-1,800. The math is simple.
Sign 2: Water Where It Shouldn’t Be, And the Leak Most People Miss
The Obvious Front-Loader Door Seal Failure
Water pooling in front of your machine after every wash screams door seal failure. This is the most common leak I repair on front-loaders, especially Samsung and LG models. Dubai’s heat makes rubber seals brittle. Mold growth from people closing the door between washes degrades the material. The seal develops cracks and tears. I replaced three door seals yesterday alone. Cost per job: AED 320-450 depending on the model. The repair takes 45 minutes if you have the right seal in stock. But here’s what makes this expensive: if you ignore a leaking door seal, water seeps behind the control panel and corrodes electronic connections. I’ve seen AED 400 seal problems become AED 1,200 control board replacements because customers waited three months.
The Hidden Hose Leak Nobody Checks
Most people never look behind their washing machine until water spreads across the floor. By then, a slow hose leak might have been dripping for weeks. Check behind your machine monthly. Look for water stains on the wall, dampness on the floor, or mineral deposits from evaporated water. Hose replacements cost AED 150-250. Water damage to your flooring costs AED 2,000-5,000. Mold remediation if water seeps into walls costs even more.
The Pump Leak That Ruins Everything
Water leaking during or after the drain cycle usually indicates pump seal failure. The pump is working but water escapes around the seal instead of going down the drain. This is mechanical failure that requires pump replacement.
Cost breakdown for pump replacement:
- Economy brands (Candy, Toshiba): AED 350-500
- Mid-range brands (LG, Samsung, Whirlpool): AED 500-700
- Premium brands (Bosch, Miele, Siemens): AED 700-1,000
The pump itself costs AED 200-400. Labor adds AED 150-300. Same-day service adds AED 100-150.
The Leak That Isn’t Actually a Leak
Sometimes customers call about “leaks” that are actually condensation or oversudsing. If you see small amounts of water only occasionally, check these first: Are you using too much detergent? High-efficiency machines need very little. Are you using regular detergent in an HE machine? That creates excessive suds that can overflow. Is your machine in an air-conditioned room? Condensation forms on cold external surfaces.
Before paying AED 150-200 for a diagnostic visit, eliminate these possibilities.
ElectroGenie Dubai offers free leak inspection with any service call, Book online now
Sign 3: Error Codes That Actually Mean Something
The Samsung “4E” Code That Drains Your Wallet
Samsung washing machines display error code 4E when water doesn’t fill properly. This seems simple but I’ve seen it indicate five completely different problems:
- Water supply turned off (free to fix, you just turn the tap)
- Inlet valve filter clogged with sediment (AED 120 to clean)
- Water inlet valve failure (AED 350-500 to replace)
- Pressure switch failure (AED 400-550)
- Control board issue (AED 800-1,200)
A good technician diagnoses the root cause before replacing parts. I’ve seen competitors replace the inlet valve for AED 500 when the actual problem was a AED 0 solution of just turning on the water supply. This is why you need a reputable service.
LG “OE” Code: The Drain Crisis
LG machines throw an OE error when water won’t drain. Nine times out of ten, this is a clogged drain pump filter or kinked drain hose. You can check this yourself in five minutes. The filter is behind a small panel at the bottom front of the machine.
I’ve done service calls where the customer paid AED 150 for me to clean a filter they could have cleaned themselves. But sometimes OE indicates actual pump failure (AED 500-700 to replace) or a faulty pressure sensor (AED 400-550).
Here’s my rule: if you clean the filter and check the hose and OE persists, call a technician. Don’t run multiple cycles trying to “fix it.” Every failed drain attempt puts stress on the pump motor and can convert a AED 400 problem into a AED 900 problem.
Bosch Error Codes: When German Engineering Fails
Bosch machines are reliable until they’re not. Their error codes are more specific than other brands, which helps diagnosis:
- E18: Drain pump blockage (DIY fix or AED 180 service call)
- E23: Water in the base tray (serious leak, AED 400-800 to diagnose and repair)
- F21: Drum not rotating (motor or belt issue, AED 600-900)
- F43: Motor locked (possible bearing failure, AED 800-1,200)
E23 is the code that scares me most. It means water has leaked into the base of the machine and triggered the safety float. This could be from any of six different failure points. Diagnosis takes 30-45 minutes.
The Whirlpool Codes Nobody Understands
Whirlpool uses letter combinations that seem designed to confuse. “Sud” or “Sd” doesn’t mean error at all. It means the machine detected too many suds and is running an extended rinse. Just use less detergent next time. But “F06 E02” means drive motor tachometer error. Translation: the motor can’t tell how fast the drum is spinning. This requires motor replacement (AED 800-1,100) or control board replacement (AED 700-1,000) depending on diagnosis.
Error Codes You Can Actually Reset
Before calling a technician for any error code, try this reset procedure: Unplug the machine for 60 seconds. Plug it back in. Select a short cycle and start. If the error clears, you likely had a glitch from a power surge or fluctuation. This happens frequently in Dubai during summer peak demand. If the error returns immediately or during the cycle, you have a real problem that needs professional attention.
Sign 4: Your Clothes Come Out Wrong
The Slow Death of Cleaning Power
This is the warning sign most people ignore longest. Your machine gradually stops cleaning effectively. First, you notice stains don’t come out. Then clothes smell musty even after washing. Eventually, you’re re-washing everything. This rarely indicates single-point failure. Usually it’s multiple degraded components: weak pump that doesn’t circulate water properly, clogged detergent dispenser that doesn’t release soap correctly, scaled heating element that can’t reach temperature, or worn agitator that doesn’t move clothes effectively.
I diagnosed this last week in a six-year-old Whirlpool top-loader in Motor City. The customer thought the machine was “tired.” Actually, the agitator dogs (the plastic parts that engage the agitator) were completely worn down. The agitator spun freely instead of gripping and moving clothes. Cost to replace: AED 280. Cost of six months of re-washing everything: immeasurable.
The Soap Scum Nightmare
If detergent residue appears on clothes after washing, you have one of three problems:
- Using too much detergent (free to fix, just reduce amount)
- Clogged detergent dispenser (AED 150 to clean professionally)
- Water temperature issue preventing soap dissolution (AED 400-600 to repair)
In Dubai’s hard water, detergent doesn’t rinse away cleanly. The minerals bind with soap to create that gray scum you see on dishes and now on your clothes. This is why I always recommend high-efficiency low-suds detergent even for standard machines.
The Spin Cycle That Doesn’t Spin
You open the door to clothes that are soaking wet and heavy. The spin cycle completed but didn’t extract water. This indicates several possible failures:
- Drain pump running but weak (AED 500-700 to replace)
- Drive belt slipping (AED 250-350 to replace)
- Motor capacitor failure (AED 300-450)
- Clutch assembly worn (AED 600-900 on top-loaders)
- Control board not signaling full spin speed (AED 700-1,000)
The diagnostic process matters here. I’ve seen technicians immediately replace the pump when the actual problem was an AED 35 belt. Choose technicians who actually diagnose instead of just swapping expensive parts.
When Your Machine Takes Forever
Cycle times that double or triple indicate efficiency problems that will only get worse. A 45-minute normal cycle that now takes 90 minutes means something is making the machine work harder.
Common causes: Scaled heating elements can’t reach temperature so the machine extends the cycle waiting for heat. A weak pump can’t circulate water properly so each phase takes longer. Failing control board misreads sensors and gets stuck in loops.
The machine still completes cycles so people ignore this warning. Don’t. Extended cycles burn more electricity (your DEWA bill increases), put extra wear on components, and usually end in complete failure within 3-6 months.
I had a customer whose electricity bill jumped AED 200 per month because her LG front-loader ran two-hour cycles instead of 60 minutes. She thought she was saving money by not repairing it. After four months, the motor burned out from excessive runtime. Motor replacement: AED 950. Total extra electricity costs over four months: AED 800. The original problem was an AED 320 heating element.
Sign 5: The Vibration Violence That’s Destroying Your Machine
The Earthquake Machine
Excessive vibration during the spin cycle is the warning sign most likely to cause collateral damage. I’ve seen washing machines literally walk across rooms. I’ve seen machines vibrate so violently they damaged floor tiles, knocked holes in walls, and destroyed adjacent appliances.
Vibration has multiple causes with very different solutions:
Unbalanced Load (Free to Fix): Large items like comforters bunch on one side. The drum spins off-center and shakes. Stop the machine, redistribute, restart. If this happens every cycle, your machine has a problem.
Failed Shock Absorbers (AED 400-600): Front-loaders use shock absorbers like car suspensions to dampen drum movement. These wear out after 4-6 years in Dubai conditions. When they fail, even balanced loads vibrate excessively.
Worn Drum Bearings (AED 800-1,200): Bearings keep the drum centered. When they wear, the drum wobbles during high-speed spin. This creates a violent vibration that damages everything nearby.
Broken Suspension Springs (AED 350-500): Top-loaders suspend the tub on springs. If a spring breaks, the tub tilts and vibrates. Usually you’ll hear metallic clanging along with the vibration.
Unlevel Machine (Free to Fix): If your machine wasn’t leveled during installation, vibration worsens over time as internal components shift. Use a spirit level. Adjust the feet until the machine is perfectly level front-to-back and side-to-side.
The Apartment Building Warning
If you live in an apartment, excessive washing machine vibration creates problems beyond your unit. I’ve had building management call me because a resident’s machine was shaking so badly it damaged the unit below. The owner faced AED 12,000 in repairs to the neighbor’s ceiling and had to replace her machine anyway.
Vibration repairs range from AED 0 (releveling) to AED 1,200 (bearing replacement). Structural damage to your building can cost tens of thousands. Act immediately if your machine walks or shakes violently.
The Bearing Failure Timeline
Here’s what most people don’t know about drum bearing failure: it happens in stages over 6-12 months. First, you hear occasional grinding during spin. Then the grinding becomes constant. Then the vibration starts. Then the bearing actually seizes.
If you catch bearing failure at the grinding noise stage, replacement costs AED 800-1,000. If you wait until the bearing seizes, the drum can damage the outer tub (AED 1,200-1,800 additional), destroy the spider arm (AED 400-600 additional), or crack the tub itself (machine totaled, AED 1,800-3,500 for replacement).
I replaced bearings last Thursday in a Samsung that was caught early. Total cost: AED 880. I replaced bearings yesterday in an LG that was ignored for four months. The spider arm was cracked and the tub seal was damaged. Total cost: AED 1,650.
When to Repair vs. When to Replace: The Dubai Reality Check
Here’s the calculation most repair guides get wrong: they don’t account for Dubai’s accelerated appliance aging or current replacement costs.
Repair if:
- Machine is less than 6 years old
- Repair cost is less than 40% of replacement cost (not 50% like elsewhere)
- Only one major system is failing
- The machine cleaned well before this problem started
Replace if:
- Machine is over 8 years old with major failure
- Repair cost exceeds AED 1,500
- This is the second major repair in 12 months
- Multiple systems are showing wear
Current replacement costs in Dubai:
- Economy brands: AED 800-1,400
- Mid-range brands: AED 1,500-2,800
- Premium brands: AED 2,800-5,500
A six-year-old Samsung with bearing failure (AED 900 repair) is worth fixing. An eight-year-old machine with bearing failure plus control board issues plus door seal problems (AED 2,000+ total) should be replaced.
I tell customers this truth: if you’re considering a repair over AED 1,200 on a machine over six years old, replacement is usually smarter. New machines use 40% less water and 25% less electricity. Your DEWA bill will drop. Modern machines have better pumps, bearings, and seals designed for our climate.
The Brand-Specific Failures I See Most Often in Dubai
LG: Door Lock Nightmares
LG front-loaders have chronic door lock mechanism failures. The lock engages but won’t release, trapping your laundry inside. Replacement cost: AED 280-400. I’ve replaced hundreds of these. LG redesigned the mechanism in 2020 models, but older models fail predictably at 4-5 years.
Samsung: The Motor and Electronics Lottery
Samsung makes great machines when they work, but when they fail, it’s usually expensive. Motor control board failures are common (AED 800-1,100). The good news is that most Samsung issues are repairable. The bad news is that parts are expensive and failures can be random rather than wear-related.
Bosch: Limescale Vulnerability
Bosch machines are engineered for soft European water. In Dubai’s hard water, their heating elements and pumps scale up faster than other brands. I’ve seen three-year-old Bosch machines with completely scaled heating elements. Prevention: run a descaling cycle every two months with citric acid or commercial descaler.
Whirlpool: Solid But Old-Fashioned
Whirlpool top-loaders are reliable but use outdated technology. Parts are inexpensive and widely available. Repairs average AED 200-500. The trade-off is that they use significantly more water and electricity than modern HE machines.
Miele: Built to Last, Expensive to Fix
Miele washing machines regularly last 12-15 years in Dubai. But when they need repair, parts cost double other brands. A Miele door seal costs AED 650 while a Samsung seal costs AED 320. Factor this into your buying decision.
The Prevention Protocol That Adds Five Years to Your Machine’s Life in Dubai
Monthly: The 10-Minute Maintenance Routine
Clean the detergent dispenser: Pull it out completely. Soak in hot water with vinegar. Scrub away residue and mold. This prevents clogs and improves cleaning performance.
Wipe the door seal: Use a cloth with a mild bleach solution. Get into all the folds where mold hides. This extends seal life by years.
Run a hot cleaning cycle: Empty machine, hottest setting, add 200ml white vinegar. This descales internal components and kills mold.
Check hoses: Look for cracks, bulges, or mineral deposits. Replace hoses every four years as preventive maintenance. Cost: AED 150 now or AED 2,000 in water damage later.
Every Three Months: The Deep Clean
Descale the machine: Dubai’s hard water requires aggressive descaling. Use commercial descaler or 500g citric acid in a hot cycle. This protects the heating element, pump, and internal plumbing.
Clean the drain filter: Located behind the bottom front panel on most machines. Expect to find lint, hair, coins, and disgusting slime. Cleaning this improves drainage and extends pump life.
Level the machine: Check with a spirit level. Adjust feet if needed. Vibration from an unlevel machine accelerates bearing wear exponentially.
Annually: The Professional Inspection
Pay AED 200-300 for a technician to inspect your machine thoroughly. We check belts, hoses, bearings, seals, and electrical connections. We identify problems before they cause failures.
This inspection pays for itself. Last month I found a worn belt during a routine inspection. Replacement: AED 280. If that belt had snapped during a cycle, it could have damaged the motor pulley (AED 450 additional) or gotten tangled in the motor (AED 900 additional).
What Not to Do (The Mistakes That Destroy Machines)
Don’t overload: Filling the drum past 3/4 full stresses every component. It wears bearings, strains the motor, and prevents proper cleaning.
Don’t use regular detergent in HE machines: The excessive suds damage pumps and leave residue in the sump that breeds mold.
Don’t leave wet clothes in the drum: Mold starts growing within 8-12 hours. That musty smell never completely goes away.
Don’t ignore small problems: That occasional grinding noise will become constant. That small leak will become a flood. That error code that resets will become permanent.
Don’t close the door between washes: This is the number one cause of mold in Dubai. Front-loaders need airflow to dry the interior.
Real Case Studies: What Actually Happened
Case Study 1: The AED 200 Problem That Became AED 2,400
Mrs. Ahmed in Dubai Marina heard grinding during spin cycles. She called but decided to “use it until it stops working completely” because she was busy. Three months later, the drum seized mid-cycle. The bearing had disintegrated. Metal shavings damaged the drum seal, spider arm, and outer tub. The motor burned out trying to turn the seized drum.
Original diagnosis: AED 880 bearing replacement Actual cost after delay: AED 2,400 for bearing, seal, spider arm, and motor Time without machine: 8 days waiting for parts
Her comment: “I thought I was saving money by waiting. I lost money and couldn’t do laundry for over a week.”
Case Study 2: The Error Code That Cost Nothing
Mr. Khalil in JBR panicked when his Samsung displayed “4E.” He called three companies. Two quoted AED 450-600 for water inlet valve replacement. We diagnosed the actual problem in five minutes: the building’s water was shut off for maintenance. He turned the water back on after maintenance finished. Error cleared.
Cost: AED 0 Time: 5 minutes Lesson: Not every error code needs repair
Case Study 3: The Ignored Leak That Destroyed a Kitchen
Mrs. Chen in Jumeirah Village Circle had a “small leak” under her washing machine. She put a towel underneath and kept using it. After six weeks, water had seeped under the flooring, through the ceiling to the unit below, and created mold throughout her kitchen walls.
Washing machine repair: AED 320 (door seal) Flooring replacement: AED 5,800 Ceiling repair for downstairs neighbor: AED 3,200 Mold remediation: AED 4,500 Total cost of ignored AED 320 problem: AED 13,820
Her insurance covered some costs but raised her premiums. She told me she noticed the leak the first week but thought “it wasn’t that bad.”
Conclusion: The Real Cost of Ignoring Warning Signs
You’ve now seen the five major warning signs plus two hidden ones that Dubai technicians diagnose every week. You understand why machines fail faster here. You know the real costs of common repairs. You’ve learned the prevention protocol that adds years to your machine’s life.
Here’s the truth most repair guides won’t tell you: every warning sign you ignore multiplies repair costs. That AED 250 belt replacement becomes AED 800 when it damages the motor pulley. That AED 400 door seal replacement becomes AED 1,200 when water corrodes the control board. That AED 800 bearing replacement becomes AED 2,400 when the bearing destroys the spider arm and tub.
Your washing machine repair is telling you something right now. Maybe it’s that occasional grinding noise you’ve been ignoring. Maybe it’s that error code that keeps returning. Maybe it’s that small leak you’re monitoring with a towel. Whatever the warning sign, it won’t go away. It will only get worse and more expensive.
Contact ElectroGenie Dubai today for fast, honest diagnosis. We’ll tell you exactly what’s wrong, what it costs to fix, and whether repair makes sense. Same-day washing machine repair service across Dubai. Call 00971564489351or book online at https://electrogeniedubai.com/
FAQ:
How much does washing machine repair cost in Dubai?
Minor repairs (cleaning, small part replacement): AED 200-400. Moderate repairs (pumps, belts, seals): AED 400-700. Major repairs (motors, control boards, bearings): AED 700-1,200. Diagnosis fees run AED 100-200 and are usually waived if you proceed with repair.
Can I repair my washing machine myself?
Simple tasks like cleaning filters, revealing the machine, or checking hoses are DIY-friendly. But anything involving disassembly, electrical components, or part replacement requires expertise. I’ve fixed dozens of machines that were damaged worse by DIY attempts. The money you save doing it yourself gets spent fixing your mistakes.
Should I repair or replace my 7-year-old washing machine?
In Dubai’s climate, seven years is old for a washing machine. If the repair costs under AED 800 and this is the first major issue, repair it. If repair costs exceed AED 1,000 or this is the second major repair, replacement is smarter. New machines are more efficient and will lower your utility bills.
How long do washing machines last in Dubai?
Expect 6-8 years for economy brands, 8-10 years for mid-range brands like LG and Samsung, and 10-12 years for premium brands like Bosch and Miele. Dubai’s hard water and heat reduce these lifespans by 20-30% compared to cooler climates.
What causes most washing machine failures in Dubai?
Hard water scaling (35% of failures), bearing wear from heat and use (25%), door seal deterioration from heat (15%), control board issues from power surges (10%), pump failures from sediment (10%), and everything else (5%). Most failures are preventable with proper maintenance.
Do I need a voltage stabilizer for my washing machine?
Highly recommended. Dubai’s power grid experiences frequent fluctuations during summer peak demand. These fluctuations damage control boards and motors. A quality voltage stabilizer costs AED 200-350 and can prevent AED 800-1,200 in repair costs.
How often should I descale my washing machine in Dubai?
Every 6-8 weeks minimum. Dubai’s water hardness makes descaling crucial. Use commercial descaler or 500g citric acid in a hot cycle. Descaling prevents scaling that causes 35% of washing machine failures in Dubai.
Can hard water really destroy my washing machine?
Absolutely. I’ve seen three-year-old machines with heating elements so scaled they look like stalactites. Hard water deposits build up inside pumps, on drum bearings, in hoses, and throughout internal plumbing. Over time, these deposits cause mechanical failures and efficiency loss.
What’s the best washing machine brand for Dubai?
Based on 11 years of repair data: Bosch offers the best build quality but needs regular descaling. LG and Samsung are good mid-range options with readily available parts. Whirlpool top-loaders are reliable but less efficient. Miele machines last longest but parts are expensive. Avoid unknown Chinese brands; parts are impossible to source.
How do I prevent mold in my washing machine?
Leave the door open between washes. Wipe the door seal weekly with a mild bleach solution. Run a hot cleaning cycle monthly. Remove wet laundry immediately after cycles end. Never let wet clothes sit in the drum overnight. In Dubai’s humidity, mold grows incredibly fast.
Why does my washing machine smell even after cleaning?
Mold has likely grown in places you can’t reach: behind the drum, in the sump, or inside the detergent dispenser housing. Professional cleaning with disassembly is required. Cost: AED 300-500. This includes removing the drum to access hidden mold growth.
Is it worth repairing a washing machine during warranty?
Always repair during warranty when repairs are free or discounted. But check warranty terms carefully. Many warranties don’t cover “wear and tear” items like door seals or filters. Some require using authorized service centers. Some exclude damage from “improper use” like hard water scaling.